Description:
Custom Paints Direct to Metal (DTM) Primer. VOC 2.1
2K DTM Primer-Surfacer with exceptionally high build and direct-to-metal properties. Very soft sanding, wet or dry after short dry times. 2K DTM Primer provides no shrinkage and the maximum in color holdout properties available.
Available in 3 colors: grey, white and black which can be blended to make different shades of grey. Suitable for: Car, Motor bike, Caravan, Commercial Vehicle and industrial industry. TYPICAL SUBSTRATES: ▪ OEM primer ▪ GRP / fibreglass ▪ Epoxy primer surfacer ▪ Polyester putties ▪ Existing finishes in good condition ▪ Etch primer
Substrates:
2K DTM High Build Primer can be used on the following substrates
- Metal
- Galvanized
- Aluminium
- OEM primer
- GRP / Fiberglass
- Body Filler
- Polyester putties
Mixing:
The mixing ratio for 2K DTM High Build Primer:
- 4 parts 2K DTM High Build Primer
- 1 part DTM Activator
The mixing ratio for 2K DTM Sealer:
- 4 parts 2K DTM High Build Primer
- 1 part DTM Activator
- 1 Part 2K Reducer
2K DTM Primer includes:
2K High Build Primer 1 Quart:
- 1 Quart High Build Primer.
- 1/2 Pint Activator.
2K High Build Primer 1 Gallon:
- 1 Gallon 2K DTM High Build Primer.
- 1 Quart DTM Activator.
SURFACE PREPARATION:
Clean and dry the surface. Sand surface with P220—P380 grit abrasive.
MIXING:
4 Parts 2k DTM Primer
1 Part Activator
Reduction of up to 10-15% with Urethane reducers
OPTIONAL MIX 4:1:1 as a SEALER (4 parts primer 1 part Activator, 1 part 2K reducer)
POT LIFE 1 Hour @ 70°F (20°C)
GUN SET UP:
Conventional
Siphon Feed: 1.6 mm – 2.0 mm (0.063” – 0.079”)
Gravity Feed: 1.6 mm – 2.0 mm (0.063” – 0.079”)
HVLP
Siphon Feed: 1.6 mm – 2.0 mm (0.063” – 0.079”)
Gravity Feed: 1.6 mm – 2.0 mm (0.063” – 0.079”)
Air Pressures
Conventional
Siphon Feed: 35-45 psi at the gun
Gravity Feed: 30-40 psi at the gun
HVLP 8-10 psi at the gun
APPLICATION:
Clean surface thoroughly using accepted body shop procedures. Sand per accepted body shop procedures for substrate being used and final clean with solvent wipe. Apply 2-3 medium coats of 2K DTM Primer with 10-15 minutes flash between coats. Do not apply more primer after 1 hour from completion.
FLASH TIME/DRY TIMES @ 72ºF / 22.2ºC:
Flash/Dry Times (Air Dry):
Flash Between Coats: 10-15 minutes
Wet Sanding: 1 hour
Dry Sanding: 1 hour
INFRA RED 15-20 minutes
Times can vary depending on the air temperature and air movement.
RE-COAT: Topcoat within 24 hours of sanding. If time exceeds 24 hours, the primed surface must be sanded and cleaned again prior to application of primer or topcoat.
SANDING: Dry & D.A.: P400—P600 Wet Sanding: P500—P600
2K DTM Primer Kit includes:
2K High Build Primer 1 Quart Kit:
- 1 Quart High Build Primer.
- 1/2 Pint Activator.
- 1/2 Pint 2K Reducer
2K High Build Primer 1 Gallon Kit:
- 1 Gallon 2K DTM High Build Primer.
- 1 Quart DTM Activator.
- 1 Quart 2K Reducer