2K Speed Clear

$65.00
/

Activator Temperatures:

Very Slow: 95°F and above
Slow: 75°F - 90°F and above
Medium: 65°F - 80°F
Fast: 60°F - 70°F

Description:

  2K Speed Clear is a high-quality clearcoat for a fast and efficient refinish (express technology), which ensures extremely fast drying by oven as well as by air.

  This special drying property offers saving potentials in terms of spray booth occupancy, stoving times as well as working time. This leads to a considerable reduction in operating costs and increases the throughput.

  Another major advantage is that 2K Speed Clear can be polished quickly after just 5 minutes drying at [ 60 °C / 140 °F ] object temperature and a cooling phase of approx. 10 minutes, polishing can begin. Alternatively, the polishing process can be started after 20 minutes of drying at [ 40 °C / 104 °C ] object temperature plus cooling phase. After 1 hour of drying at room temperature, the polishing capability is also suited for spot repairs or partial resprays. Easy and safe application with results of highest quality.
  • Premium 2K Urethane Clear
  • Excellent Hardness; Chemical Resistance & Flexibility

The mixing ratio:

  • 2 parts Clear-coat
  • 1 part Activator

2K Speed Clear Kits:

1 Gallon 2K Speed Clear Kit: Total Mix - 1.5 Gallons of Clear-coat.

  • 1 Gallon Clear-coat.
  • 2 Quarts Activator

1 Quart 2K Speed Clear Kit: Total mix - 1.5 Quarts of Clear-coat.

  • 1 Quart Clear-coat.
  • 1 Pint Activator.

Application:

SURFACE PREPARATION:

EXISTING FINISH: Sand surface with P600-P800 wet or P500-P600 dry, and then clean with Cleaner/Degreaser. Mask object/area to eliminate unwanted overspray. Use a tack cloth to remove any surface contaminates that may have settled on the basecoat.

Dry and cure times are dependent on air movement, temperature and film builds.

 

RECOATING:

2K Speed Clear may be repaired and recoated after 12-24 hours at 70° F/21° C. 2K Show Clear may be repaired and recoated when force dried after 1 hour cool down.

EQUIPMENT CLEANING:

Clean equipment immediately after use according to local regulations.

 

POLISHING:

Air Dry:             After 24 hours

Force Dry:           1 hours after cool down.

Sanding:             Use 2000 grit wet or finer. Or use 2000 DA or finer.

Compounding:  Use finishing compound. Apply a thin ribbon of material to the area to be polished. Use a double-sided wool polishing pad or a foam pad. Maintain air polisher or variable speed buffer at 1800-3000 rpm. Remove excess finishing compound with a clean, soft cloth prior to applying finishing polish.

Metal Flake Application: "Dry Flake"

Apply our  Metal Flakes over any base color to produce a real custom effect, most customers use a black Basecoat. We recommend adding the Metal Flake to our Flake Carrier but you can add them to a Automotive solvent or water based Clearcoats, Clear basecoats and Resin's. Depending on how heavy you want the flake effect, will depend on how much you will need.

Always spray test panels before spraying you product or project to see the effect you desire.

  • Start by prepping your project as you would any other paint job. (Sand, Prime, etc.)
  • Apply 2-3 coats of Base coat.
  • Add 5g to 100g of Dry Metal Flake to a Clear base coat or lacquer and stir well.
  • Apply the 1 - 5 coats of Metal Flake until you get the effect you desire. 
  • Apply a Clearcoat until the Metal Flake is fully covered.

Metal Flake Fx Application: "Paint"

METAL FLAKE FX is an EASY to apply Metal Flake paint. Metal Flake FX is highly concentrated with our Metal Flake and full coverage can be achieved with in a few coats, which then can be 2K clear coated or be used as a base for our Candy effect paints.

  • Always spray test panels before spraying your product or project.
  • Start by prepping your project as you would any other paint job. (Sand, Prime, etc.)
  • Apply 2-3 coats of Basecoat leaving 10-15 minutes between coats.
  • Leave 60 minutes before applying the effect color to ensure basecoat is fully dry.
  • Stir paint well before adding Reducer. Mix Metal Flake Fx 2-1 with Reducer & stir well.
  • Apply 2-5 coats of Metal Flake Fx depending on the effect you desire. Leave 20-30 minutes between coats. Ensure its fully 
  • Leave 60 minutes before applying a 2k Clearcoat.

This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.

You may also like

Recently viewed