Bonding, Glues & Seam Sealers: Bonding & Seam Sealers

$0.00
/

SEM Products:

Dual-Mix - Heavy Bodied Seam Sealer - 40377 - Black is a high viscosity, two-component epoxy for use on interior or exterior seams, joints and voids.

Dual-Mix - High-Build Self Leveling Seam Sealer - 39777 is a two-component, controlled flow epoxy ideal for use on roof seams, drip rails and trunk seams.

Dual-Mix - Multi Purpose Panel Adhesive - 39747 is a two-component epoxy for panel bonding of steel, aluminum, SMC and fiberglass.

Dual-Mix - Flexible Urethane Foam - 39357 is a two-component, urethane, expanding foam that stops vibration and dampens sound in most voids.

Dual-Mix - Patch Panel Adhesive - 39897 is a two-component adhesive for quickly bonding metal panels without the use of an external primer. 

3M Products:

3M - EZ Sand Multi Purpose Repair Material - 05887 is a ready-to-use 2-part epoxy finishing adhesive material that dries to a flexible hardness, ideal for repairing plastic parts such as bumper covers and body panels. It applies easily from a 3M applicator gun mixing nozzle, with no pre-mixing or measuring. It is quickly sandable for excellent featheredge, and paintable in as little as 30 minutes.

3M - Super Fast Plastic Repair - 04247 is a high performance, two-component, semi-rigid, urethane adhesive. This fast-setting adhesive produces rapid results and offers excellent wide gap filling capabilities. This repair adhesive can be used for a variety of applications, does not run or sag and withstands a wide range of temperatures.

High Teck Products:

High Teck - White - Seam Sealer - 9274 is a fast acting seam and joint sealer. With a quick, 30 minute drying time, it maintains flexibility and withstands oxidation, salt water, gas and other solvents.

High Teck - Black - Seam Sealer - 9275 is a fast acting seam and joint sealer. With a quick, 30 minute drying time, it maintains flexibility and withstands oxidation, salt water, gas and other solvents.

Metal Flake Application: "Dry Flake"

Apply our  Metal Flakes over any base color to produce a real custom effect, most customers use a black Basecoat. We recommend adding the Metal Flake to our Flake Carrier but you can add them to a Automotive solvent or water based Clearcoats, Clear basecoats and Resin's. Depending on how heavy you want the flake effect, will depend on how much you will need.

Always spray test panels before spraying you product or project to see the effect you desire.

  • Start by prepping your project as you would any other paint job. (Sand, Prime, etc.)
  • Apply 2-3 coats of Base coat.
  • Add 5g to 100g of Dry Metal Flake to a Clear base coat or lacquer and stir well.
  • Apply the 1 - 5 coats of Metal Flake until you get the effect you desire. 
  • Apply a Clearcoat until the Metal Flake is fully covered.

Metal Flake Fx Application: "Paint"

METAL FLAKE FX is an EASY to apply Metal Flake paint. Metal Flake FX is highly concentrated with our Metal Flake and full coverage can be achieved with in a few coats, which then can be 2K clear coated or be used as a base for our Candy effect paints.

  • Always spray test panels before spraying your product or project.
  • Start by prepping your project as you would any other paint job. (Sand, Prime, etc.)
  • Apply 2-3 coats of Basecoat leaving 10-15 minutes between coats.
  • Leave 60 minutes before applying the effect color to ensure basecoat is fully dry.
  • Stir paint well before adding Reducer. Mix Metal Flake Fx 2-1 with Reducer & stir well.
  • Apply 2-5 coats of Metal Flake Fx depending on the effect you desire. Leave 20-30 minutes between coats. Ensure its fully 
  • Leave 60 minutes before applying a 2k Clearcoat.

This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.

You may also like

Recently viewed